2 pack - Stock tail bushing for all Thrasher versions
Stock wear ring for Thrasher and Thrasher XT
Stainless Steel Jet Protector V1/V2
Compatable with V1 and V2 Thrasher Jet Boats, these extremely rugged protectors are made from 18 gauge stainless steel sheet. These parts will take a beating and will allow you to run your Thrasher in shallow water over rock and protect your jet drive during even the hardest bashing sessions.
Thrasher Steering Servo Motor
Stock servo motor for Thrasher and Thrasher XT. Includes horn and stainless steel mounting screws.
This drive shaft seal is located between the pump body and the motor mount to significantly reduce the flow of water into the hull. One seal is used per boat. Includes two seals.
Steering Nozzle Thrasher V1 and V2
Stock steering nozzle for Thrasher V1 and V2
Billet Aluminum Alloy Impeller
CNC Machined 6061-T6 Aluminum Alloy Impeller. These high performing impellers are designed to maximize pump performance. Made in the USA, machined to the highest quality standards and finished with an anodized surface to increase resistance to corrosion and wear.
Thrust Nozzle with Tail Bushing
Stock Thrust Cone with tail bushing for Thrasher and Thrasher XT
Thrasher Ride Plate - Fast Plane
This is the first of many ride plates that we will be releasing. These attached very easily from the outside of the boat with a single screw. This upgrade will make your hull plane out very quickly, keep you pump in the water and hooked up more often for increased speed and handling. Improved cornering with reduced slide is also achieved with this simple upgrade.
Esc assy (2s-6s battery format)
Thrasher ESC - for all versions of Thrasher
Thrasher V1 and V2 Pump Tuning Kit
You can expect up to a 20% increase in thrust from this pump tuning kit. Get the most from your pump by taking out the additive effect of stacked tollerences inherent in all assemblies. Each of the components in your pump assembly have a +/- tollerence from each respective manufacturing process. A pumps performance is increased by minimizing the gap between the pump wall and the impeller blades. This kit allows you to test a sequesnce of three wear rings that are all .5mm increments thicker than the previous, with the first being .5mm thicker than your stock wear ring. You chose the wear ring that allows the smallest gap without the impeller touching the ring and your pump is tuned! It is that simple and you will notice the difference - guaranteed! ***Important*** You will need to install a PBBR kit or block off your stock bilge in order to realize the increased thrust potential of this upgrade.
Sponson Fins - Set of 4
This is a complete set of 4 sponson fins (2 port and 2 starboard) for Thrasher Jet Boats. If you are adding sponson fins to a Thrasher that does not already have a sponson fin kit installed, you will need to purchase a sponson fin kit, which includes these fins as well as mounting hardware and instructions.
Thrasher V1 and V2 lid with captive screw and pin
Thrasher V1 and V2 lid with captive screw and pin. White only, graphics sold separately.
CNC machined billet aluminum impeller for Thrasher V3, 26mm pitch
Automatic Power Bilge System
This is a one of a kind advancement for RC boating. Designed to bolt on and plug in to all Thrashers. This system can also be mounted to any RC boat with a customized mounting bracket. This bilge pump system utalizes a unique waterproof control module that senses if your RC boat is rightside up or upside down before it will trigger the bilge pump if water is sensed inside the boat. All controls, brackets, and wiring is included. There is no wiring or soldering required. This is a bolt on and plug in system. No additional channel is required. This is a fully automatic system. Check out this demonstration video:
How to install in a Thrasher V3:
How to install in a Thrasher V1/V2:
Addition hull vent kit
This upgrade adds an additional vent to your hull allowing it to self right faster and more reliably. The kit is quick to install but will require you to drill a hole and insert a port using a soldering iron. A 5mm drill and a soldering iron is required.
4065 1350kv Brushless Motor
The original Thrasher brushless motor. Fits all Thrasher version. 2000 Watts of high torque power. This is the motor that started it all, the first of it's kind debuting our patent pending long shaft design. These motors are unique to Streamline RC with oversized stainless steel ball bearings and a balanced and integrated motor/drive shaft for increased efficiency and significantly lower vibration at high rpm.
Full size servo kit with Billet Aluminum horn and quick trim adjust system
This is a heavy duty steering upgrade from the already tough stock Thrasher steering system. In this kit you will receive a full size waterproof servo, an adapter plate for mounting this servo in your Thrasher, and a complete steering linkage with boot, servo arm, and quick trim adjust system. This kit not only makes your Thrasher steering system more rugged and waterproof, but it makes trim adjustments much easier with acces to a set screw for trim adjustment from the top of the boat without moving the servo moutn plate.
Stock lid pin for all versions of Thrasher RC Jet Boats
Transmitter and Waterproof Receiver
Transmitter and Waterproof Receiver for Thrasher Jet Boats
Full size servo adaptor kit - 48.8/41.6/10/6
This kit comes with all that you will need to install your full size servo into a Thrasher V1 or V2. This kit comes with an adaptor plate, a steering rod, a quick trim adjusts system and a billet aluminum horn. Because servos can vary in mounting dimensions, please check the drawing in the attached image to make sure that your servo will fit before making your purchase. Another consideration is the height that your servo will fit the horn above the mounting plate as well as how deep your servo body will sit below the mounting plate. This plate is designed for the servo horn to sit on a spline that has a top surface that is 20 mm above the servo mount surface of the plate and it is designed for a servo that is no deeper than 27 mm from the mounting surface to the bottom of the servo. If you have a favorite servo that will not mount using this mounting plate, please send me an e-mail at email@example.com and I will consider adding a suitable plate to our offering. Please view our how to installation video prior to installation.